Zycoo have release firmware version 1.1.0 for their U20 and U50 Coovox IPPBX. The is a combination of fixes and new features. Firmware can be downloaded from the Zycoo website.
Details of the release for both models are similar and full list of changes for the U20 can be seen below:
Read Before Upgrade:
- This patch is only intended for upgrading to CooVox-U20 V1.1.0. Please check details of this release and decide if it is necessary to upgrade your system.
- CooVox series firmware releases are not cumulative and therefore CooVox must be operating from the previous firmware release e.g. V1.0.5 Patch 2 before upgrading to V1.1.0.
- A Configuration file is not included in the upgrade so you are not required to backup your configuration before upgrading. If a previous version of backup file is restored after upgrade, it will lead to abnormal GUI functionality. You should however create a new backup file once you have upgraded to V1.1.0.
- Clear your browser cache to display the firmware version correctly.
Background Fixed:
1. When flash storage exceeds the defined value, it will be uploaded automatically.
2. Adjusted the maximum silence time to 10s in voicemail.If no voice is detected within 10 seconds then it will be considered to be an invalid voicemail.
3. Fixed audio codec configuration problem in IAX2 protocol.
4. Define the Caller Name as Null when incoming call originates from analog port.
5. Allow the wildcard character to be used in DOD number in the DOD Settings page.
6. Adjusted the number of call logs to save a maximum of 20000 call logs.
7. Fixed a problem where the reboot operation from GUI will fail after restoring a backup configuration that has a different password to the current system password.
8. Fixed a problem preventing auto-detected fax’s being forwarded to an extension from an analog line.
9. Adjusted callback function so incoming calls will be hung up before the line answers(Except PSTN line).
10. Modification of driver:
1) Support special character”* + #” in GSM dial number;
2) GSM module can refresh strength of GSM signal automatically.
11. Fixed a bug where caller ID of recording file is changed to Unknown on the phone in blind transfer.
12. Fixed a BLF problem for analog extension.
GUI Fixed:
13. Fixed a rewriting problem in “Network Settings”, “IPv6 Settings” and “VLAN Settings” pages.
14. Allow an administrator to enable and configure the call forward prompt on Call Forward page (Administrator GUI).
15. Strengthen the recovery function of backup files.It is now possible to choose recovery PBX or network settings when restoring a backup.
16. Adjusted record list to reverse order. The new generated file will be displayed at the top.
17. On the VoIP Trunks page, Auto Fax Detection can now be configured even without authentication.
18. Adjusted the language options to be synchronized with system language in VoIP trunk settings.
19. Removed links to trunk settings on the Operator page.
20. Adjusted the Smart DID page to not allow deletion of the rule when only one smart DID rule remains.
21. Fixed a problem where“$” cannot be used in login password.
22. Resolve a display problem on firewall configuration page with Arabic and Persian language.
23. Adjusted VoIP trunk settings so username and certification name can bea maximum of 64 digits.
24. Modified the Auto Provision function to allow renewal of configuration content for Yealink devices;
GUI Added:
25. Added “call duration” on “Record List” page (Administrator & Extension User GUI).
26. Added Russian language option in the GUI.
27. Added “Timeout” on IVR page(The maximuminterval time for prompt playback).
28. Added the extension number in destination ID field and also the ring-group or queue the extension is associated with on Call Logs page. E.g.: Extension 806 which belongs to ring-group 640 receives a call from caller 801.
29. Added DST(daylight saving time) to Tehran Time.
30. Added the option “Keep the current network settings” when reset to factory default.
31. Added the option “Ring Timeout” in Global Analog Settings page, which is used to define the time to hang up the call when there isn’t a ring signal before the FXO answers.
32. Added the option “Enable Attended Transfer Caller ID” in Options page. Once enabled, the
Caller ID will be sent to the transferred destination when transferring the call.
33. Added more brands to Auto Provision:
1) Support auto-provision of Cisco IP Phone SPA303 (TFTP(DHCP Option66) only, DOES NOT support PnP);
2) Support auto provision of MOCET IP Phone IP3032E (Default is PnP, also support TFTP(DHCP Option66));
3) Support auto provision of Hanlong IP Phone UC860P, UC842, UC802P, UC840P, UC804P, UC806P (Default is PnP, also support TFTP(DHCP Option66)).